Unboxing the t12 prism Photo Booth Shell Enclosure
Hey guys!
Welcome. This is Ray with RBA photo booths Inc.
Today I am gonna be discussing the unboxing of the t12 prism and before I do that I want to discuss the size and the weight of the box. What I have here is a tape measure and what I am going to do is I am gonna go ahead and give you the measurements of this box. Just to see you guys know exactly how big is this box gonna be and how much it weighs.
So the front back of this is 18 and 38 inches. The box left to right is 24 inches. The top to bottom of this box is 18 and 3 ¼ (quarter) almost 19 inches. The exact weight is 44.1 pounds of this box. That’s an empty shell, okay.
I already cut it. So I have already basically opened. I cut the tape. So this is how it’s gonna look like. The first thing you are gonna notice is there gonna be two foams right on top of that and these foams are styrofoam. They are protecting the top shell of the head and what you are actually gonna do is its kind of hard for me to get this thing out so what I am gonna do that I am gonna take away all these styrofoam and I am going to put it all this aside so that’s the reason why I am doing this because I want to be able to get a good grip when I lift it out. Okay so there is all this and we do this to protect this shell wallet on passes.
So this system has the headshell of the photobooth of the t12 prism. The next one I gonna take out is the stand. Again the stands are also shrink wrapped. I am gonna put that right there. This is the lower portion of the stand and this is the upper portion of the stand. Okay! Make sure you guys don’t throw anything away. The reason is why is because you don’t know if we put the brackets inside or outside. Sometimes our guys who are packing this up will put the bracket into a small plastic bag and shift it inside but a lot of time what I have seen them do is to put it inside the stand or inside the shell. This is the base plate, okay. I am gonna put the base plate here for now and what we have is the yoke. put the yolk right there and what I am gonna do which you should also do when you gonna get the packet is to make share that there is nothing in here left. Okay!
Because again, we don’t know if they put the bracket inside so just to be sure, make sure that everything is empty and then we can take everything you took out it. First the foam and put it back in the box so that it’s not scattered everywhere and then go ahead and close this back and I am gonna go ahead and put this thing over and we gonna talk about the shell.
Once everything is all laid out, you pretty much took everything out in the box. We are gonna do next is we are gonna unscrew the screw that is inside because if you are wondering where all the knobs are, well, it’s inside these shells and what I am gonna do is I am gonna show you where is that. This way you guys don’t get confused and think that we forgot to send it to you. So here it is.
The knob is actually is located right here and yokes reverse. This is the upper portion of the stand. We will take this guy also reverse. We did this so that you guys don’t lose it. Well, technically we did it so that UPS doesn’t lose it just in case. They get crazy with the shipment. We at least know that everything is attached and nothing goes missing so if you are wondering where all the stuff is located, wonder no more and right over here if you are wondering how to open the back of the t12 prism. All you need is a magic coder. Take the coder and then twist and then open. So here we have the knobs are inside and I reverse that. Take this guy. Put it there and then this one is the straw flash. We are gonna take it out also. Now bear in mind that there is a remote for the t12, I mean for the t12 prism remote. LEV is right here. The case has got a little velcro, we put it right here. This is for here, this t12 LEV light, and this one also has a remote. You can use one remote for both but just in case you lose it, you still have this one and this one is actually for this, right here, okay. The LED that drops into this. The bottom portion over. So the next segment we are gonna do this that we are gonna assemble everything together, alright. So the first thing we gonna do is we gonna put all the knobs in the right places.
Right there. So easy that is and then I am gonna twist it and there you have it the t12 prism. What we gonna do is we are gonna go ahead and we are gonna open up the front and make sure it’s tight. We are gonna put the straw flash in here. So you can see the complete top portion of the t12 prism, alright.
So there you have it guys. That was unboxing the t12 prism. If you liked what you saw, please hit the subscribe button underneath this video channel, okay and that will motivate us to do more video content for you guys to watch. The next segment, what we are gonna do next is I am gonna be talking about how to put the t12 system together. That’s gonna help you build a photo booth system. It’s basically gonna give you the guidance on how to put everything together in terms of the computer, the lightings, even connecting the printer. We are gonna discuss even the software, type of photobooth software you should be using, all the good stuff. But first, hit the subscribe button and if you guys are ever interested in buying a t12 prism, it’s on our website. It’s in stock, ready to ship anytime, okay. The website is www.rbaphotobooth.com. If you are not comfortable ordering it from our website and you wanna call somebody and speak to a real person you can call us toll-free 1866 412 0160 and once again this is Ray with RBA photo booth, signing out.
Thank you!